Have a question about your camera? Post it in the comments! Someone will probably reply to your question.
CAMAPP365
  • Home
  • Technical
  • Camera type
    • Doorbell
  • Reviews
  • Cease service
  • VIDEO
camapp365
Home TOSEE

ToSee Battery WiFi Camera User manual

November 16, 2021
in TOSEE
1
Share on FacebookShare on Twitter
Contents hide
Appearance Introduction
Installation Instructions
Installation Instructions
Feature
Device Connection
Technical Parameters
Q&A
The device cannot connect to WiFi.
The device is online and there is a triggering event, but the phone does not receive push information.
What power supply methods does the device support?
What storage methods does the device support?
PDF download

Appearance Introduction

Appearance Introduction
NameDescription
Infrared LightWhen the ambient light is not enough, enable the infrared light to increase the brightness of the environment
Light SensorUsed for collecting the ambient brightness value; when the illumination is below 2Lux, enable the infrared light
Pickup DeviceUsed for collecting the environment sound and the voice intercom
PIR detectionWhen the human body moves in front of the device, it can generate a trigger signal to the mobile phone
LensUsed for collecting the image video
Indication LightRed Light Flashing Slowly: System waits for WiFi  configuration. 
Blue Light Flashing Slowly: System is in normal working  condition. 
Red and Blue Lights Flashing Alternately: System WiFi connection failed
Appearance Introduction
NameDescription
Reset KeyDevice working status; press and hold for 5 seconds to restore factory settings
TF CardInstall the TF card to support local video
The Battery SwitchTurn off and turn on the device battery power through the switch key
USB InterfaceCharge the device battery through the USB interface
Bracket Mounting HoleMounting on the wall using accessory brackets
SpeakerUsed for sending system alert tones and the voice intercom
Rear Cover ScrewsInstall the battery to power the device by opening the rear cover

Note: You need to open the bottom silicone to see the function interface as shown in the figure.

Installation Instructions

Installation Instructions

As shown in the figure, remove the screws and open the back cover

Installation Instructions

Push up the snap button upwards to open the battery compartment and install the battery

Installation Instructions

Pay attention to installation polarity: “+” positive pole should be installed inwards (Improper installation can cause damage to the device)

Installation Instructions

Installation:

① The human body induction effective distance is 3-5 meters, so please adjust the monitoring angle according to the actual situation.
② Please avoid the installation position where the temperature changes too much, such as heat source, airoutlet, etc. which will cause frequent
alarms to the device.


Alarm Adjustment: The device defaults 10 seconds to trigger alarm. If you need to adjust the sensitivity, please go to the Device Settings page.

See also  TOSEE For PC – Use TOSEE On Your Computer

Feature

FeatureTwo 3400mAh original 18650 batteries can be used for 2-3 months
FeatureFull HD resolution
FeatureSupport the phone wake-up device
FeatureSupport the 2.4G wireless connection
FeatureTwo-way Audio
FeatureSupport the PIR human body infrared detection, when someone lingers in the doorway,immediately send alarm information to the smartphone APP
FeatureDay and night mode switches automatically. The clear and distinct image will help to ensure the safety of you and your family

Device Connection

① Download ” tosee” in the mobile application market Tosee and open the APP software.(For a better user experience, please allow all notification permissions to avoid not getting notifications)

② Click the at the top right corner of the APP to add device, select + Add Device and go to next step.

Device Connection

③ Enter the setting page of the mobile phone system according WiFi tothe prompt. Connect the WIFI sent by the device ToSee , return to APPand continue to the next step.

Device Connection

④ On the Network Configuration page, fill in your home WiFi account and password, and start the configuration.

Device Connection

⑤ Set the device administrator password for sharing and management

Device Connection

⑥ Device added successfully, please change the name of the device.

Device Connection

If you need to reconfigure your WiFi network, press and hold the reset key for 5 seconds,The red light will flash slowly and you can follow the instructionsagain to connect

Technical Parameters

Visual AngleDiagonal 104°
Infrared Light850mm 6pcs
WIFISupport 802.11b/g/n
AudioTwo-way intercom with echo cancellation
VideoTF card (15 seconds each time)
Storage8G/16G/32G
Battery2 pcs of 18650 batteries
PushSpeed Push in 2 Seconds
Wake-up DurationWithin 600ms
Wake-up MethodPIR human body induction wake-up Phone Active Wake-up
Power ConsumptionStandby current 300uA
Working current 250mA

It can be used for 2-3 months if working 30 minutes a day with 2 pcs of 18650 batteries (6800mAh).

Q&A

The device cannot connect to WiFi.

1. Please confirm that the wireless network to be connected is the 2.4G protocol
2. Make sure that the indication light is in the red light flashing slowlystate
3. Check if the account password is correct and whether there are extra spaces

See also  TOSEE For PC – Use TOSEE On Your Computer

The device is online and there is a triggering event, but the phone does not receive push information.

Turn on the “Self-Starting” on APP and turn on the notification function on the “Apply Permissions”,Turn off the “Battery Optimization” and aslo the “End the APP at Background and Reset Screen”
(Different mobile phone manufacturers have different optimization methods, please refer to the actual situation)

What power supply methods does the device support?

1. The device can work alone with 18650 batteries
2. Possible to charge the device through USB

What storage methods does the device support?

The device can use the TF card for video storage, or it can use the real-time recording and capture functions of the mobile phone for storage

PDF download

ToSee Battery WiFi Camera User manual下载
Previous Post

How To SetUp Danale NVR Security camera system? (Ultimate Manual Guide)

Next Post

EKEN Video doordell User Manual

Related Posts

TOSEE For PC

TOSEE For PC – Use TOSEE On Your Computer

Comments 1

  1. RONNY LUYTEN says:
    1 year ago

    DEZE APP IS NIET MEER TE KRYGEN OP PLAY???????

    Reply

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Search

Camera APP

Best Micro SD Card for Security camera

We think the Samsung Pro Endurance is the best choice, designed for use in security cameras to help keep your video files safe, incredibly durable, and backed by a 3-year warranty.

1. Top pick : Samsung Pro Endurance(128GB )

2. Budget pick: Sandisk High Endurance U3(64GB )

3. High Capacity Pick: Sandisk Ultra A1(128GB)

Doorbell

Without Subscription Doorbell

Camapp365 is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.

  • About
  • Privacy & Policy
  • contact us
Have a question about your camera? Post it in the comments! Someone will probably reply to your question.

© 2019-2023 camapp365

No Result
View All Result
  • HOME
  • Technical
  • Camera Type
    • Doorbell
  • Reviews
  • CEASE SERVICE
  • contact us

© 2019-2023 camapp365